Navigation: Cash register preparation >

Detailed information about connecting all supported peripherals to the touch cash register can be found in this chapter.

Composition of the stand for 14" cash register stand

1.Use the cross screwdriver and 3 bigger screws (4*8) to attach the stand to the base.

2.Use 4 smaller screws (4*6) to attach the touch cash register to the stand.

* Click on the image to display the full version.

top

Composition of 8" cash register stand

1.Attach the back stand holders to the back part of the cash register.

2.Use a hex or Allen key to tighten softly the four short screws for fastening the cash register to the stand. Put the covering stickers on the screws and put the silicone coasters on the bottom part of the stand.

3.Attach the PVC pocket to the back part of the stand with two long screws and two nuts. Place any advert you wish inside the PVC pocket.

4.If you are also using a customer display, do not attach the PVC bag and instead screw the nuts and bolts to attach the two stands together.

* Click on the image to display the full version.

top

Dotypos UNIVERSAL

1.Assemble the stand and use four screws to attach it to the back part of the touch cash register.

2.Plug the USB printer cable into any USB connector on the sides of the cash register. Now connect the power adapter to the printer, plug it into the socket and turn the printer on.

3.If you have an Ethernet cable available for the Internet connection, plug it into the RJ45 connector between the USB ports on the left-hand side of the cash register.

4.Plug the power adapter connector in the DC-IN socket and then plug the feeding cable into the socket.

5.If the cash register does not turn on automatically, use the back button on the register to turn it on. Your touch cash register is now ready for operation.

* Click on the image to display the full version.

top

Dotypos COMPLETE

1.Assemble the stand and use four screws to attach it to the back part of the touch cash register.

2.Plug the USB printer cable and the bar code reader into any USB connectors on the sides of the cash register.

3.Plug the Cash drawer cable into the RJ45 connector at the back of the printer.
(Some drawer types do not have the cable firmly connected, so you have to connect it both to the printer and the drawer. Find the connection plug on the bottom side of the drawer.)

4.Now connect the power adapter to the printer, plug it into the socket and turn the printer on.

5.If you have an Ethernet cable available for the Internet connection, plug it into the RJ45 connector between the USB ports on the left-hand side of the cash register.

6.Plug the power adapter connector in the DC-IN socket and then plug the feeding cable into the socket.

7.If the cash register does not turn on automatically, use the back button on the register to turn it on. Your touch cash register is now ready for operation.

* Click on the image to display the full version.

top

Dotypos MOBILE

This set consists of and 8" touch cash register and wireless Bluetooth printer. You do not have to connect any other devices.

1.Plug the tablet via the power adapter into the socket and turn it on.

2.Plug the battery into the bottom part of the printer (if not placed in the printer already).

3.Connect the power adapter to the printer and then plug it into the socket. Let the printer charge.

* The printer may already be paired with the tablet (depending on the package that was purchased). For further information please read the printer guide you will find in the package.

If the cash register does not charge after connecting to the power source, leave it turned off and charging for 3-5 hours. The battery will have then been charged and the cash register will start charging.

After first switching the Android system on, if it does not start (the Dotypos logo is displayed for a long time), hold down for about 15 seconds the button POWER to switch the cash register off. Now switch the cash register on again and it will start smoothly.

To print properly from Dotypos MOBILE (8" cash registers), disable the Android system function Standby intelligent power saving in Android settings » Battery (see next paragraph).

top

Connecting powered peripherals

If you bought Dotypos Mobile together with a bar code reader or printer, follow this sequence to connect it to the touch cash register (a more detailed connection sequence with pictures can be found in the chapter Bar code reader connection).

1.Turn the touch cash register on and display the list of installed applications. In the list, click on the item Settings. This will get you to the Android system settings.

2.Now select Security and on the page deactivate the option Vypnout OTG ACA.

3.Go back to Settings, now select Battery and deactivate the option Intelligent power saving standby.

4.Connect the Y cable to the cash register’s micro USB port. Connect the power supply adapter to the USB connector (male) on the longer side of the cable. Connect the bar code reader or USB printer to the other USB connector (female) on the shorter side of the cable. The special Y cable allows the cash register to be powered continuously.

5.If you have a USB printer connected, the cash register must be connected to the power supply all the time! When running on batteries, printing will not work.

top